Top seller
No results were found for the filter!
10% Saved
MS Labs Drive by Wire Modul MS Labs Drive by Wire module for using an electronically controlled throttle body in combination with an MS3. Using an electronically controlled throttle body offers many advantages over a conventional throttlebody. For example, the idle...
€417.69 * €464.10 *
Swap Package ME221 to MS3 Mini MX-5 NA/NB/NBFL The ultimate upgrade package for your MX-5 NA/NB/NBFL! We offer you the opportunity to upgrade your ME221 ECU purchased from us to an MS3 Mini, and at an unbeatable price. The basic requirement for this is an already purchased ME221 ECU...
From €1,558.40 *
Transi Productions speedo module MX-5 NA/NB/NBFL Electronic speedometer sensor unit from Transi Productions for use in transmission conversions that do not have a direct speed sensor installed on the transmission (e.g. BMW transmission swap). Also suitable for all types of gear ratio...
€106.67 *
EGT kit MX-5 NA/NB/NBFL Sensor kit for exhaust gas temperature for use in combination with MS3 ECU´s suitable for MX-5 NA/NB/NBFL. With the kit it is possible to feed the exhaust gas temperature values into the standalone ECU via the temperature sensor used....
From €142.17 *
Link ECU CAN Lambdacontroller incl. Bosch 4.9... Link ECU lambda controller including Bosch 4.9 LSU lambda sensor for connecting the lambda sensor to the Link ECU. Link thus offers an easily configurable solution for the users of their control units. Included in the delivery are: 1x...
€484.21 *
Link ECU MX-5 NA 2 Plug 89-95 Link ECU standalone ECU G4X suitable for MX-5 NA, which have 2 plugs on the ECU The control unit is simply inserted into the original control unit housing of the MX-5 and replaces the standard control unit circuit board there. Here is an...
€1,393.85 *
Bosch wideband lambda sensor LSU 4.9 Original Bosch wideband lambda sensor LSU4.9 with a wide range of applications. Ideally suited for use with standalone ECU´s. Also used in the AEM lambda display we offer.
€155.06 *
Prosport wiring loom for oil pressure sensor... Connection wiring loom suitable for Prosport fuel/oil pressure sensors as a replacement or for connecting a CanChecked. One end of the cable fits directly onto the Prosport oil pressure sensor. The other side is suitable for the...
€13.72 *
Sensor for oil temperature gauge 50-150°C Temperature sensor for VDO oil temperature gauge with 1/8" NPT thread. Measuring range: +50 - +150°C Thread: 1/8" NPT Resistance values: 322.8 - 18.6 ohms Output: 1-pin via ground
€25.66 *
Sensor for VDO Oil pressure gauge 0-5 bar /... VDO oil pressure sensor with a range of 0-5 bar and a warning contact at 0.25 bar. Measuring range: 0-5 bar Thread: 1/8" NPT conical short Resistance values: 10-184 ohms Output: 1-pin via ground Warning contact: 0.25 bar ± 0.15 bar
€101.55 *
D-Sub extension cable 2m Renkforce serial Renkforce serial extension cable with 2m length in beige with potted housing. One side of the cable has a D-SUB plug (male) and the other side has a D-SUB socket (female). Perfect for connecting a serial port standalone ECU to a serial...
€8.88 *
Transi Productions ECU Standard MX-5 NA 2 Plug... Engine ECU suitable for MX-5 NA with 1.6 liters (2 plugs on the ECU) from Transi Productions. The ECU can be used for all conversions that we also offer in-house. Whether it's a ITB, turbo or supercharger conversion, you are on the safe...
€716.08 *