CANchecked CAN Bus Extension Module MCE18

Preview: CANchecked CAN Bus Extension Module MCE18

CANchecked CAN Bus Extension Module MCE18

€204.99 *

Prices incl. VAT plus shipping costs

delivery in approx. 2-6 weeks

Order number: 248487

If you have any questions about TÜV registration or orders to Switzerland, please do not hesitate to contact our competent partners in the respective country:

Mail to SPS Partner in Switzerland (Garage Obrist)

MCE18 stands for Multifunction Can Bus Extension with 18 ports - why is this module needed? Our... more

Close menu

Product information "CANchecked CAN Bus Extension Module MCE18"

MCE18 stands for Multifunction Can Bus Extension with 18 ports - why is this module needed? Our displays (MFD28, MFD32, MFD32S) have four analog inputs. However, for some applications this may already be too few and more inputs are needed. It is obvious to map these via the flexible Can Bus protocol. For this, the sensors are connected to the CANchecked MCE18 and sent via Can Bus to the device to be received - e.g. one of our MFD28 displays.

But also freely programmable ECU have only a limited number of inputs. These can be expanded very easily with our module and sent directly to the ECU.

Already tested with:

MaxxECU
Ecumaster
LinkECU
Syvecs (coming soon)
Haltech (coming soon)

Scope of supply:

MCE18 with housing
Connector superseal 34pin (TE 4-1437290-0)
Pins superseal 1.0 20AWG (TE 3-1447221-4)
3 jumpers

Connector pin out diagram:

Pin	Name	Description
1	+12V	12V power supply
2	GND	Ground supply
3	+5V	5V Sensor power supply
4	+5V	5V Sensor power supply
5	VBUS	5V USB (mostly red)
6	D+	D+ USB data (mostly green)
7	D-	D- USB data (mostly white)
8	USB GND	USB ground (mostly black)
9	D7	Digital input 7
10	D0	Digital input 0
11	D8	Digital input 8
12	A0	Analog input 0
13	D2	Digital input 2
14	A6	Analog input 6
15	A2	Analog input 2
16	A3	Analog input 3
17	A4	Analog input 4
18	SGND	Sensor ground
19	SGND	Sensor ground
20	SGND	Sensor ground
21	D1	Digital input 1
22	A1	Analog input 1
23	D6	Digital input 6
24	D3	Digital input 3
25	A8	Analog input 8
26	CANH	Can Bus High
27	CANL	Can Bus Low
28	SGND	Sensor ground
29	+5V	5V Sensor power supply
30	+5V	5V Sensor power supply
31	D5	Digitaler Eingang 5
32	D4	Digital input 4
33	A5	Analog input 5
34	A7	Analog input 7

If you remove the front 4 screws, you can pull off the housing. There are three jumpers on the back.

1. JP1 plugged activates the 120 Ohm resistor for the Can Bus
2. JP2 plugged in activates the 1K1 pullup resistor for A1 and A2
3. JP3 plugged activates the 1K1 pullup resistor for A6 and A7

By default, all jumpers are removed.

Default Can Bus Stream
The data of the inputs are polled and transmitted every 50ms (20Hz - changeable). The data is transmitted as "unsigned big endian". As soon as 12V and ground are connected, the green status LED on the rear panel is on. Can Bus ID: 0x700 (Base Data CAN ID - changeable).